external harddrive cabinet: Prolific PL3507 Combo Device

the device(info from gscanbus):
SelfID Info
-----------
Physical ID: 0
Link active: Yes
Gap Count: 63
PHY Speed: S400
PHY Delay: <=144ns
IRM Capable: No
Power Class: +15W
Port 0: Connected to parent node
Port 1: Not connected
Init. reset: No

CSR ROM Info
------------
GUID: 0x0050770E000001CD
Node Capabilities: 0x000083C0
Vendor ID: 0x00005077
Unit Spec ID: 0x0000609E
Unit SW Version: 0x00010483
Model ID: 0x00000001
Nr. Textual Leafes: 1

Vendor: PROLIFIC TECHNOLOGY, INC.
Textual Leafes:
Prolific PL3507 Combo Device

AV/C Subunits
-------------
N/A

my kernel setup (running 2.6.0-test5-mm1)
#
# IEEE 1394 (FireWire) support (EXPERIMENTAL)
#
CONFIG_IEEE1394=y

#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
# CONFIG_IEEE1394_OUI_DB is not set

#
# Device Drivers
#

#
# Texas Instruments PCILynx requires I2C bit-banging
#
CONFIG_IEEE1394_OHCI1394=y

#
# Protocol Drivers
#
# CONFIG_IEEE1394_VIDEO1394 is not set
CONFIG_IEEE1394_SBP2=y
# CONFIG_IEEE1394_SBP2_PHYS_DMA is not set
# CONFIG_IEEE1394_ETH1394 is not set
# CONFIG_IEEE1394_DV1394 is not set
CONFIG_IEEE1394_RAWIO=y
# CONFIG_IEEE1394_CMP is not set
#
# SCSI device support
#
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=y

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
# CONFIG_SCSI_REPORT_LUNS is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set

first i get(text from dmesg):

ieee1394: sbp2: Logged into SBP-2 device
ieee1394: sbp2: Node 0-00:1023: Max speed [S400] - Max payload [2048]
Vendor: WDC WD25 Model: 00JB-00EVA0 Rev:
Type: Direct-Access ANSI SCSI revision: 06
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)

then i get(a little later, from dmesg):
ieee1394: sbp2: aborting sbp2 command
0x1a 00 08 00 04 00
ieee1394: sbp2: aborting sbp2 command
0x00 00 00 00 00 00
ieee1394: sbp2: reset requested
ieee1394: sbp2: Generating sbp2 fetch agent reset
ieee1394: sbp2: aborting sbp2 command
0x00 00 00 00 00 00
ieee1394: sbp2: reset requested
ieee1394: sbp2: Generating sbp2 fetch agent reset
ieee1394: sbp2: aborting sbp2 command
0x00 00 00 00 00 00
ieee1394: sbp2: reset requested
ieee1394: sbp2: Generating sbp2 fetch agent reset
ieee1394: sbp2: aborting sbp2 command
0x00 00 00 00 00 00
scsi: Device offlined - not ready after error recovery: host 0 channel 0
id 0 lun 0
SCSI device sda: drive cache: write through
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
ieee1394: Node added: ID:BUS[0-00:1023]
GUID[0050770e000001cd]
ieee1394: Host added: ID:BUS[0-01:1023] GUID[0090f500000e841c]
ieee1394: unsolicited response packet received - no tlabel match

after this the device wont show up as /dev/sda, any ideas ? :)

this message is also posted at:
http://sourceforge.net/tracker/index.php?func=detail&aid=806194&group_id=2252&atid=102252

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf
_______________________________________________
mailing list Linux1394-user@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/linux1394-user
Received on Mon Sep 15 14:10:16 2003